Black Dog Machine
SW-DRUM
$92
Sold by: Go Gear Direct
In Stock at Go Gear Direct
Easy Returns – merchant policy applies
Price Tracked – we monitor this deal 24/7
Price History
Loading price history...
Customer Reviews
Loading reviews...
Product Details
As with all Black Dog Machine products, Black Dog Machine S&W-DRUM is 100% made, designed, and assembled in the USA. Manufacture's Lifetime Warranty. Recommended Ammunition: Federal, CCI/Blazer, American Eagle. Use a round nosed bullet. Stay away from hollow points. Ammunition not listed will not feed well in our products. Black dummy rounds: The plastic black dummy rounds are an important part of the drum assembly. They feed the ammo from the drum body to the tower. BDM does not recommend using dummy rounds as real bullets. Winding Rotor: Pulling the rotor counter clockwise and letting go will most likely damage the drum. It can cause the internal followers to break. Loading the Black Dog Machine LLC Drum Hold the round drum body in the left hand with the body at a 45 degree position. With your left thumb pull the rotor counterclockwise enough to slip in 2-3 rounds with the right hand repeat until drum is full. To unload pull rotor slightly counter clockwise to relieve the tension. The rounds will fall out the front with short counterclockwise and clockwise pulls of the rotor. Disassembly of Drum Hold the drum and remove center screw with a 5/32 Allen wrench. Remove the two #4-40 Allen screws from top ears with a 3/32 Allen Wrench. Hold drum horizontal in the left hand with the nut side of the drum housing facing up (this is the back of the drum). Lift the back cover off while holding on to the front drum housing. Wind the rotor counterclockwise until the follower and dummy round stack comes out of tower. (Please note: dummy rounds apply to the AR15.22 and 10/22 drums only). Hold the pressure on the rotor and remove the dummy stack along with the follower. Gently let go of the rotor and remove it and the tower. The tower can be disassembled forcleaning or can be cleaned as a unit. There should be no need to remove the spring but it can be removed by taking off back plate. The spring is not under tension inside the rotor when not assembled and can be easily be removed. Assembly of Drum The rotor can be installed in 1/4 turn intervals using thedrum housing's axle timing slots. The AR15.22 and Puma/PPS50 Drum has 1 1/2 turns from our factory. The tension can be decreased or increased; we recommend 1 1/2 minimum to 2 turns maximum. The turns is established by finding the follower hole on the outside of rotor. For two turns orientate this hole so it is straight up in line with the feed tower opening. For 1 1/2 turns orientate the hole so it is down and opposite the feed tower; for 1/4 turn intervals orientate the rotor hole in the 90 degree position. Now line up the tail of the spring in the center with the nearest axle slot and pushrotor in place. Tilt the rotor out at the top and insert the feed tower. Holding the drum housing and tower in the left hand count 1-3/4 full turns from the follower hole.Hold tension on rotor with left fingers and install follower and dummy rounds. Make sure dummy rounds go in nose first and that the rubber band is positioned in the center hole of each round. See Photo 8 Start letting off the rotor tension while using a finger or thumb to guide the dummy stack and follower up into the tower. Be sure that the follower doesn't come out of hole, if it does it can be pushed back in with the Allen wrenchor a finger. Install the cover, 2 ear screws, flat head bolt, and nut. A snug fit will work, no need to torque the bolt. Pull the rotor back out of the tower 2-3 times to line up the dummy round stack. The drum is now ready to load, enjoy! Note: The power spring may relax over time. This is expected and is not a bad thing. To adjust, simply take the drum apart and reset your wind to 1 1/2 - 2 turns. Sub-Assembly of Follower and Dummy Stack (AR15.22 only) AR15 tower requires 10 dummy rounds, one follower, and one rubber band. To assemble dummy stack first feed the round end of the rubber band down through the hole in the follower and pull it through. Insert roundend of band into the hole near the rim of the dummy round and snap it towar
- Category
- Sporting Goods > Outdoor Recreation
- Brand
- Black Dog Machine
- SKU
- 103-000004